Before setting up the Samesay SRA7010G, look at the sofa, not just the TV cabinet. This 7.1.2-channel Dolby Atmos system includes a soundbar, a separate wireless subwoofer and two battery-powered satellite speakers. The satellites give you physical surround speakers, but they also need suitable locations and a practical way to recharge.
Check three things first: where both satellites will sit, how you will recharge them, and which audio output your TV can use. If any of those is unclear, resolve it before approving a sample or committing to an installation.
1. Check the room before placing the rear speakers
Start at your main listening seat. Look for two stable positions beside or behind the listening area, then compare those positions with the placement diagram supplied with your unit. Check the speaker labels and keep left and right on their intended sides. If the sofa backs onto a wall, check whether side placement fits the manufacturer's instructions rather than forcing the speakers into the gap behind it.
Check the soundbar against the available space below the screen, including clearance for the TV's remote sensor. Plan a separate position for the subwoofer and check its power connection. A wireless audio link removes the need for a signal cable between the bar and the subwoofer; it does not remove the subwoofer's power requirements.
If you cannot place both satellites safely or access them for charging, a simpler system may suit the room better. Compare virtual surround and physical rear speakers before deciding which configuration to sample.
2. Connect the TV and verify audio before testing surround
- Identify the labelled ports. For HDMI TV audio, connect the TV port marked ARC or eARC to the soundbar's corresponding TV audio port, following the supplied manual. A regular HDMI socket on the TV is not necessarily an ARC/eARC port.
- Select the right output and input. Set the TV to use the external audio system and select the matching input on the bar. Follow the TV manufacturer's instructions for any required ARC, eARC or HDMI control settings.
- Confirm basic playback first. Play familiar content and check that dialogue comes through the bar. If there is no sound, recheck the port labels, output settings and selected input before changing the satellite setup.
- Check the format separately. Hearing TV audio does not prove that the bar is receiving Dolby Atmos. Confirm that the content, source device, TV settings and connection support the format you intend to test. Check the reported input format if your equipment makes it available.
The SRA7010G also lists an optical input. If your TV does not offer ARC/eARC, optical is an option to evaluate for TV audio, but do not assume it supports the same formats as HDMI. See the HDMI ARC versus optical comparison before choosing the connection.
3. Make sure satellite charging fits daily use
Samesay lists a 7.4 V / 2600 mAh satellite battery for this model. That figure is a battery specification, not a playback-time estimate. Use the instructions for the supplied unit to identify the charging connection, approved accessories and charge indicators.
- Check access: Can you reach each satellite and use the specified charging method without moving furniture or dismantling a mount?
- Check the indicators: Can you distinguish low battery, charging and fully charged states using the supplied instructions?
- Check a normal session: If runtime matters, charge the sample as directed and log the playback duration, volume setting and content. Use those conditions when comparing samples rather than relying on a claim about how many movies it can play.
4. Accept the sample only after these checks
Start with a working TV connection. Then check the subwoofer and both satellites using the model's instructions. For left/right verification, use material with known surround-channel cues; ordinary dialogue or a quiet scene may not exercise both satellites.
| Check | What to record |
|---|---|
| TV audio | TV model, connection used, selected input and any audio settings required for playback. |
| Left and right satellites | Whether each known channel cue plays from the intended side at the planned speaker positions. |
| Subwoofer and satellite reconnection | What happens after a normal restart and whether any step in the manual is needed to restore playback. |
| Charging and pack contents | Whether the supplied accessories match the packing list and whether the manual makes the charge states clear. |
If a check fails, record the input, content, speaker position and observed indicators before changing settings. This makes it easier to reproduce the issue and distinguish a TV output problem from a speaker connection or charging problem.

